亚洲av手机在线观看不卡,亚洲AV网站,亚洲AV无码AV男人的天堂,亚洲AV无码AV日韩AV网站

Synchronous Pulley Aluminum plate Synchronous Belt V-belt V-Pulley Rack Specialty Tapes

product

product

Rubber synchronous belt

Double sided toothed synchronous belt

PU open synchronous belt

Rubber opening synchronous belt

DA HTD2000 8M Flour Machine Belt

Polyurethane series synchronous belt

01

Synchronous Belt

02

Rubber Synchronous Belt

03

Double-sided Timing Belt

04

PU open timing Belt

05

Rubber opening Belt

06

Flour Machine Timing Belt

07

Polyurethane Timing Belts

Basic parameters

Synchronous belt drive consists of an endless belt whose Inner surface has equally soaced teeth and of belt wheels which have the corresponding teeh and is a kind of new type belt drive which has synhesized all the good points og belt drive, chain drive and gear drive, while working, the teeth o the belt and the gullets of the gear joggle each other to transmit the motion and the dynamic force.

Synchronous belt drive has such features as exact transmission ratio, non-sllding, constant velocity ratio which can be gained, even motion, absorption ofvibration, little noise,the bia range of transission ratio which can normaly reach 0.98, compacting tructure.The suitability to multi-axis transmission,no need of lubrication,no pollution and so on. Therefore,the product can notmally work well in the places where no pollution is allowed and where the working condition is poor and can widely be used in machinery drives, such industry as automebiies, machine tools, textile, chemical engineering, light industry, mining,indtruments, oil industry and so on as well as all kinds of other machinery drive.

Synchronous belt we produced have a lot of advantages:anti-wearing out, low elongation rate and high strength, resistant to wide temperature range, non-aging, ozone resistant,etc. now we have over 30 types timing belt with more than 2000 specification.And we can supply matched pulleys. All these can meet our customers perfectly . The property of our products have reached or surpassed the internaional standard.



1.Physiconechanical Property of Synchronous Belt

Ltem Trapezoid tooth Atctooth
XL L H XH XXH 3M 5M 8M 14M 20M
Tensile strenght N/mm 80 120 270 380 450 90 160 300 400 520
Elongatlon Referenve load 60 90 220 300 360 70 130 240 320 410
Atreference load Elongation 4.0
Hardness(Shore A) 75±5
Adhesion strength of cloth 5 6.5 8 10 12 - 6 10 12 15
Core rope adhesion strength 200 380 600 800 1500 - 400 700 1200 1600
Gear shearing intensith 50 60 70 75 90 - 50 60 80 100

2.Belt length calculation section

L':2c+1.57(Dp+dp)+(Dp-dp/4c) Calculation of centre distance between axises
L':Approximate pitch line length of belt C=B+(√B2-2(Dp-dp)2)/4
C:Centredistance between axises B=L-1.57(Dp+dp)
Dp:Pitch diameter of the bigger belt pulley L:Pitch line length of the belt (mm)
dp:Pitch diameter of the smaller belt pulley  
Basic parameters

1.Type of rubber synchronous belt & the dimension of section Automotive Timing Belt Dimensions List

TYPE Pitch Tooth height Belt thickness
ZA 9.525 1.91 4.10
ZB 9.525 2.29 4.50
ZH 9.525 3.50 5.50
YH 8.00 3.04 5.20
ZR 9.525 3.20 5.40
YR 8.00 2.00 5.10
ZS 9.525 3.53 5.70
YS 8.00 2.95 5.20
ZAS 9.525 2.32 4.62
ZBS 9.525 2.76 5.06
S8MYU 8.00 3.05 5.30
FS 9.525 3.05 5.35
MY 8.00 3.06 5.21
MR 9.525 3.54 5.69
RU 9.525 3.44 5.40
ZLB 9.525 2.70 5.05

2.T Type industral rubber synchronous belt

Type Pitch Tooth height Belt thickness Belt thickness Teeth number range
MXL 2.032 0.51 1.14 40 40-1012
XL 5.080 1.27 2.30 50 30-650
L 9.525 1.91 3.60 40 26-530
H 12.70 2.29 4.30 40 40-472
XH 22.225 6.35 11.20 40 53-200
XXH 31.750 9.53 15.70 40 56-144
T2.5 2.5 0.7 1.30 40 30-400
T5 5 1.20 2.20 40 20-444
T10 10 2.50 4.50 40 26-567
T20 20 5.00 8.00 40 54-138
AT5 5 1.20 2.70 50 20-444
AT10 10 2.5 5.00 50 26-567
AT20 20 5.00 8.00 50 54-138

3.Arc tooth industrial rubber synchronous belt

Type Type Pitch Tooch height Belt thichness
HTD 3M 3 1.17 2.4
5M 5 2.06 3.8
8M 8 33.36 6.00
14M 14 6.02 10.00
20M 20 8.4 13.20
STPD/STS S2M 2 0.76 1.36
S3M 3 1.14 1.9
S4.5M 4.5 1.71 2.81
S5M 5 1.91 3.4
S8M 8 3.05 5.3
S14M 14 5.3 10.2
RPP/HPPD P2M 2 0.76 1.36
P3M 3 1.15 1.9
P5M 5 1.95 3.5
P8M 8 3.2 5.5
P14M 14 6.00 10
Basic parameters

1.Double-sided Timing Belt

·The pitch and tooth profile of double-sided timing belt are same as the single-sided timing belt.

·Double-sided timing belt has two standard forms:

Model DA Symmetrical arrangement of the two-side teeth;

Model DB Staggered arrangement of the two-side teeth.

2.Dimension of double sided timing belt、special profile belt

Special Profile Belt Synchronous Belt
Type Pitch length
(mm)
Teeth No Type Pitch length
(mm)
Teeth No
HTDI200-8M 1200 150 HTD.DA1200-8M 1200 150
HTDI440-8M 1440 180 HTD.DA1400-8M 1400 175
STPD1600-8M 1600 200 HTD.DA1440-8M 1440 180
RPPI760-8M 1760 220 HTD.DA1600-8M 1600 200
RPPI760-10M 1760 176 HTD.DA1760-8M 1760 220
RPPI880-10M 1880 188 HTD.DA1680-8M 1680 210
RPPI920-10M 1920 192 HTD.DA1920-8M 1920 240
RPPI740-12M 1740 145 HTD.DA2000-8M 2000 250
RPPI848-12M 1848 154 HTD.DA2400-8M 2400 300
Pitch Code Nominal Height
mm In
D-MXL 1.53 0.06
D-XL 3.05 0.12
D-L 4.58 0.18
D-H 5.95 0.234
D-XH 15.49 0.61
D-XXH 22.11 0.87
D-T2.5 2.00 0.08
D-T5 3.40 0.134
D-T10 7.00 0.275
D-T20 13.00 0.52
HTD.DA-8M 8.17 0.32
Basic parameters

1.PU open timing Belt

PU open timing belt is made of ther moplastic polyurethare material and high strength fine steel Wire. It is Of high wear-resistance and strength. It keeps a good condition inb transmission with small production tolerances. PU open timing belt is of the stable transmission, wide application. Long transmission distance ad accurate size.

·It resists ageing. Hydrolysis, ultraviolet ray UVA and ozone.

·Operating temperature: -30℃~+80℃,it can bear max. +110℃ within a short perlod of time.

·Highly oil and grease resistant.

·It resists partial acid and alkali corrosion.



2.PU open Belt Type

Type Pitch Pb Tooth height a Belt thickness h STANDARD WIDTH
MXL 2.032 0.51 1.14 025 031 037 050 075 100
XL 5.08 1.27 2.3 025 031 037 050 075 100 150 200
L 9.525 1.91 3.6 050 075 100 150 200 300 400 600
H 12.7 2.29 4.3 050 075 100 150 200 300 400 600
XH 22.225 6.35 11.2 100 150 200 300 400 600
Type Pitch Pb Tooth height a Belt thickness h STANDARD WIDTH
T2.5 2.5 0.7 1.3 6 10 16 25
T5 5 1.2 2.2 6 10 16 25 32 50
T10 10 2.5 4.5 12 16 25 32 50 75 100
T20 20 5.0 8 25 32 50 75 100 115
Type Pitch Pb Tooth height a Belt thickness h STANDARD WIDTH
AT3 3 1.1 1.9 10 20 25 50
AT5 5 1.2 2.7 6 10 16 25 32 50
AT10 8 2.5 4.5 16 25 32 50 75 100
AT20 14 5.0 8 25 32 50 75 100 115
Type Pitch Pb Tooth height a Belt thickness h STANDARD WIDTH
HTD3M 3 1.17 2.4 6 9 12 15 25 30 50
HTD5M 5 2.10 3.7 10 15 25 50 100 150
HTD8M 8 3.38 5.6 10 15 20 30 50 85 100
HTD14M 14 6.01 10 25 40 55 85 100 115
Type Pitch Pb Tooth height a Belt thickness h STANDARD WIDTH
S3M 3 1.14 1.9 6 9 12 15 25 30 50
S5M 5 1.85 3.35 10 15 25 50 100 150
S8M 8 3.05 5.3 10 15 20 30 50 85 100
S14M 14 5.3 10.2 25 40 55 85 100 115
Type Pitch Pb Tooth height a Belt thickness h STANDARD WIDTH
RPP5M 5 2.0 3.8 10 15 25 50 100 150
RPP8M 8 3.2 5.4 10 15 20 30 50 85 100
RPP14M 14 6 10 25 40 55 85 100 115
Basic parameters

1.Rubber Opening Belt

PU open timing belt is made of ther moplastic polyurethare material and high strength fine steel Wire. It is Of high wear-resistance and strength. It keeps a good condition inb transmission with small production tolerances. PU open timing belt is of the stable transmission, wide application. Long transmission distance ad accurate size.

·It resists ageing. Hydrolysis, ultraviolet ray UVA and ozone.

·Operating temperature: -30℃~+80℃,it can bear max. +110℃ within a short perlod of time.

·Highly oil and grease resistant.

·It resists partial acid and alkali corrosion.



2.Rubber open Belt Type

Type Pitch Pb Tooth height a Belt thickness h STANDARD WIDTH
MXL 2.032 0.51 1.14 025 031 037 050 075 100
XL 5.08 1.27 2.3 025 031 037 050 075 100 150 200
L 9.525 1.91 3.6 050 075 100 150 200 300 400 600
H 12.7 2.29 4.3 050 075 100 150 200 300 400 600
XH 22.225 6.35 11.2 100 150 200 300 400 600
Type Pitch Pb Tooth height a Belt thickness h STANDARD WIDTH
T2.5 2.5 0.7 1.3 6 10 16 25
T5 5 1.2 2.2 6 10 16 25 32 50
T10 10 2.5 4.5 12 16 25 32 50 75 100
T20 20 5.0 8 25 32 50 75 100 115
Type Pitch Pb Tooth height a Belt thickness h STANDARD WIDTH
AT3 3 1.1 1.9 10 20 25 50
AT5 5 1.2 2.7 6 10 16 25 32 50
AT10 8 2.5 4.5 16 25 32 50 75 100
AT20 14 5.0 8 25 32 50 75 100 115
Type Pitch Pb Tooth height a Belt thickness h STANDARD WIDTH
HTD3M 3 1.17 2.4 6 9 12 15 25 30 50
HTD5M 5 2.10 3.7 10 15 25 50 100 150
HTD8M 8 3.38 5.6 10 15 20 30 50 85 100
HTD14M 14 6.01 10 25 40 55 85 100 115
Type Pitch Pb Tooth height a Belt thickness h STANDARD WIDTH
S3M 3 1.14 1.9 6 9 12 15 25 30 50
S5M 5 1.85 3.35 10 15 25 50 100 150
S8M 8 3.05 5.3 10 15 20 30 50 85 100
S14M 14 5.3 10.2 25 40 55 85 100 115
Type Pitch Pb Tooth height a Belt thickness h STANDARD WIDTH
RPP5M 5 2.0 3.8 10 15 25 50 100 150
RPP8M 8 3.2 5.4 10 15 20 30 50 85 100
RPP14M 14 6 10 25 40 55 85 100 115
Basic parameters

Flour machine synchronous belt parameters

Special toothed wedge belt for flour machine
1760RPP8M-36PK 1760RPP8M-48PK 1760RPP8M-28PK 1760RPP8-34PL
1764RPP12M-34PL 1440RPP8M-28PK 1440HTD8M-28PK 1440RPP8M-48PK
1440HTD8M-48PK 1778RPP14M-29PL 1778HTD14M-29PL 1600RPP8M-24PK
1884RPP12M-34PL 1552RPP8M-28PK 1368RPP8M-48PK 1760RPP10M-26PL
1848RPP12M-34PL 1880RPP10M-34PL    
Double sided toothed synchronous belt for flour machine
DA-2400-HTD8M DA-2000-HTD8M DA-1600-HTD8M DA-1400-HTD14M
Basic parameters

1.T Type industral rubber synchronous belt

Type Pitch Tooth height Belt thickness Belt thickness Teeth number range
MXL 2.032 0.51 1.14 40 40-1012
XL 5.080 1.27 2.30 50 30-650
L 9.525 1.91 3.60 40 26-530
H 12.70 2.29 4.30 40 40-472
XH 22.225 6.35 11.20 40 53-200
XXH 31.750 9.53 15.70 40 56-144
T2.5 2.5 0.7 1.30 40 30-400
T5 5 1.20 2.20 40 20-444
T10 10 2.50 4.50 40 26-567
T20 20 5.00 8.00 40 54-138
AT5 5 1.20 2.70 50 20-444
AT10 10 2.5 5.00 50 26-567
AT20 20 5.00 8.00 50 54-138

2.Arc tooth industrial rubber synchronous belt

Tooth shape code Type Pitch Tooch height Belt thichness
HTD 3M 3 1.17 2.4
5M 5 2.06 3.8
8M 8 33.36 6.00
14M 14 6.02 10.00
20M 20 8.4 13.20
STPD/STS S2M 2 0.76 1.36
S3M 3 1.14 1.9
S4.5M 4.5 1.71 2.81
S5M 5 1.91 3.4
S8M 8 3.05 5.3
S14M 14 5.3 10.2
RPP/HPPD P2M 2 0.76 1.36
P3M 3 1.15 1.9
P5M 5 1.95 3.5
P8M 8 3.2 5.5
P14M 14 6.00 10